Extron-electronics MTP U T A D Setup Guide Bedienungsanleitung PDF herunterladen

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

MTP U T A D • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate an Extron MTP U T A D universal transmitter.

Preparing the Mounting Surface

NOTE: Use a wall box with a depth of at least 2.5 inches (6.4 cm).

1. Place the wall box against the installation surface and mark the opening guidelines.

TIP: Use a level to properly orient the opening.

2. Cut out the material from the marked area.

3. Secure the wall box with 10-penny nails or #8 or #10 screws, leaving the front edge ush with the outer wall or furniture surface.

4. Run all required cables (see Rear Panel Connections) and secure them with cable clamps.

Front Panel Inputs

INPUTS

VIDEO

AUDIO INPUT

COMPUTER INPUT

MONITOR OUT

S-VIDEO

PWRVID S-VIDYUV PC

AUDIO

EDID SELECT

CONTACT

PRE-PEAK

50Hz REFRESH

RPr

YUV

1234

12V

.5A MAX

OUTPUT

Side

8 9

a Plug a computer (VGA) video source into the Computer Input 15-pin HD connector.

b Plug a VGA monitor into the Monitor Out 15-pin HD connector.

c Plug a high denition or standard denition component video source into the YUV RCA

connectors.

d Plug a composite video source into the Video RCA connector.

e Plug an S-video source into the S-video 4-pin mini-DIN connector.

f Plug a stereo audio source into the audio RCA connectors.

g Plug a stereo audio source into the 3.5 mm mini jack connector.

Rear Panel Connections

INPUTS

VIDEO

AUDIO INPUT

COMPUTER INPUT

MONITOR OUT

S-VIDEO

PWRVID S-VIDYUV PC

AUDIO

EDID SELECT

CONTACT

PRE-PEAK

50Hz REFRESH

RPr

YUV

1234

12V

.5A MAX

OUTPUT

Side

8 9

Terminate a TP cable as shown below at right. Connect it between the transmitter Output port

and the receiver Input port (both ends need to match).

Wire the 5-pole captive screw connector for the contact closure control of input selections

as shown below. To select a video input as the transmitter output, momentarily tie the

Wire color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

12345678

Insert Twisted

Pair Wires

Pins:

assigned pin for that format to ground.

Wire the 2-pole captive screw connector for the included external 12 VDC, 1 A power supply

(see image and grounding instructions on the next page).

ATTENTION: Do not connect these devices to a computer or telecommunications

network.

Contact closure input selection connector wiring:

Pin Format Pin Format Pin Ground

1 Composite 3 YUV 5 Ground

2 S-video 4 PC

NOTE: If you are using an

Enhanced Skew-Free™ A/V

cable, use the TIA/EIA T568A

standard only.

1 2

Inhaltsverzeichnis

Seite 1 - IMPORTANT:

IMPORTANT:Go to www.extron.com for the complete user guide, installation instructions, and specifications before connecting the product to the power s

Seite 2 - MTP U T A D • Setup Guide

68-1674-50 Rev. D 01 13MTP U T A D • Setup GuideExtron Headquarters+800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East+1.714.49

Kommentare zu diesen Handbüchern

Keine Kommentare

Extron-electronics MTP U T A D Setup Guide Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Extron-electronics MTP U T A D Setup Guide herunter. Extron Electronics MTP U T A D Setup Guide User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Extron-electronics MTP U T A D Setup Guide