68-1844-02 Rev. A07 13HDMI DA4 and HDMI DA6User GuideHDMI®Distribution Amplifiers
50/60 Hz100-240V ~ 0.3 A MAXHDMI DA4RS-2324321Tx Rx GREMOTEOUTPUTSINPUT3 41 250/60 Hz100-240V ~ 0.3 A MAXHDMI DA6RS-232436521Tx Rx
Use a HDMI cable to connect the input source to the female HDMI socket on the rear panel (b in figure 2).The connectors are
RS‑232 communication between the distibution amplifier and a host PC can be used to update firmware or configure the
Use the mini Type B USB port on the front panel to connect the distribution amplifier to a host computer to update firmware or
3. Click Next. The next screen of the Wizard opens:Figure 6. InstallingtheSoftwareAutomatically4. Select Install the software automatically (Rec
OperationThis section of the manual provides information on: z Front Panel Features z EDID MinderHDMI DA6HDMI DISTRIBUTION AMPLIFI
The USB Config port is used for SIS configuration, monitoring, and firmware updates. This port can be used as an alternative to the rear pa
EDID Minder ensures that the connected source sees the EDID of a display, even if a display is not connected. Depending on the EDID mode se
X%Rate1Rate Video Audio X%Rate1Rate
The following footnotes apply to the EDID table on the previous page:1Rate Type z PC: These
WARNING: This symbol, D, when used on the product, is intended to alert the user of the presence of uninsulated dangerou
MountingThe HDMI DA unit can be mounted in any of the following locations: z Desktop Placement z Rack Mounting z Under-desk MountingA
SIS CommandsThis section provides information about the SIS commands that are used to configure the HDMIDA4 and HDMI DA6. The following topics are dis
When programming in the field, certain characters are most conveniently represented by their hexadecimal rather than their AS
E01 — Invalid output channel number (too large)E10 — Invalid commandE13 — Invalid value (too large)
Command ASCII Command(host to unit)Response(unit to host)Additional DescriptionHDCP Authorized DeviceEnable or disable HDCP authorizationEEX#HDCP} Hdc
HDMIDA4andHDMIDA6•UpdatingFirmware 19Updating FirmwareUpdates to the HDMI DA Series firmware are released periodically on the Extron website. Yo
HDMIDA4andHDMIDA6•UpdatingFirmware 20To obtain the latest version of firmware for your distribution amplifer
HDMIDA4andHDMIDA6•UpdatingFirmware 21To load a new version of firmware to the switcher using F
HDMIDA4andHDMIDA6•UpdatingFirmware 229. In the Open dialog box, navigate to the new firmware file, which has an S19 extension, and double‑click
HDMIDA4andHDMIDA6•UpdatingFirmware 23In the Add Device dialog box, the path to the new firmware file is displayed in the Path field.Figure 12. P
© 2013 Extron Electronics. All rights reserved.All trademarks mentioned in this guide are the properties of their respective owner
HDMIDA4andHDMIDA6•UpdatingFirmware 24Figure 13. FirmwareLoaderScreenwithaHDMIDA4Added11. If you want to remove a device from the Devi
Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +
Notifications the following are used: Attention indicates a situation that may damage or destroy the product
Introduction 1About the HDMI DA4 and HDMI DA6 ... 1Features ...
HDMIDA4andHDMIDA6•Contents vi
IntroductionThis guide describes the function, installation, and operation of the HDMI DA4 and HDMIDA6. Unless otherwise stated, the terms “distribut
Automatic input cable equalization — to 50 feet at 1080p/60 with 8‑bit color when used with Extron HDMI Pro Series cable. Actively conditions incoming
InstallationThis section of the guide describes the following topics concerned with the installation and setup of the HDMI DA4 and HDMI DA6 distributi
Kommentare zu diesen Handbüchern