68-1384-01 Rev. B07 10Multi-Rate HD-SDI / SDI Fiber Optic TransceiverFOX 3G HD-SDIUser GuideFiber Optic Transceivers
Connections and SettingsAll connectors are on the rear panel (figure 4).12V 0.3A MAXFOX HDSDIHD/SDI INPOWERBUFFERED OUTPUTSMODEOPTICALRxTx1 21
d Buffered Outputs connectors — In any FOX 3G HD-SDI configuration, connect a digital display to these BNC connectors. See Transceiver Configurations f
CAUTIONS: This product is intended to be supplied by a Listed Power Unit marked “Class 2” or “LPS,” rated 12 VDC, 1.0 A minimum. Always use a power s
Fiber Compatibility IndicationsYou must use the proper fiber cable for your transceivers. Each transceiver indicates its fiber compatibility, singlemode
Reference InformationThis section discusses the specifications, part numbers, and accessories for the FOX 3G HD-SDI. Topics that are covered, include:•
Maximum receiver sensitivitySinglemode ... -18 dBm, typicalMultimode ... -12 dBm, typicalOptical loss budge
Enclosure dimensions ... 1.0" H x 4.3" W x 3.0" D (quarter rack wide)(2.5 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes
Mounting AccessoriesMounting Kit Part NumberRSF 123 3-inch deep 1U rack shelf kit 60-190-20RSB 123 3-inch deep 1U rack shelf 60-604-21RSU 126 6-inc
Mounting the TransceiverCAUTION: Installation and service must be performed by authorized personnel only.The 1-inch high, quarter rack width FOX 3G H
Rack shelf mounting instructionsOn the 6-inch and 9.5-inch rack shelves, the transceiver unit can be mounted in the front or the rear of the rack.1.
This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipme
Furniture MountingUnder-Furniture MountingThe unit can be mounted under a horizontal surface using an optional MBU 125 under-desk mounting kit (part #
Through-furniture mountingThe transceiver can be mounted through a desk or other furniture using an optional MBD 129 through-desk mounting kit, part #
Projector MountingThe transceiver can be mounted on a projector bracket using either of the following optional Extron projector mounting kits:• PMK 3
3. If the power supply is connected to the transceiver, use the two included tie wraps to strap the power supply to one of the brackets.NOTE: The PM
PMK 350 mountingMount the transceiver to a PMK 350 bracket as follows:1. Remove the front and rear plates from the PMK 350 (figure 13), using a Tweeke
6. Assemble the U-bolt and the following parts in the following order (figure 14):a. Pass the legs of the U-bolt through the slotted holes on the mou
Extron® WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of pur
FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule
ContentsIntroduction ... 1About this Manual ... 1About the FOX 3G HD-
IntroductionWARNING: The FOX 3G HD-SDI units output continuous invisible light, which may be harmful to the eyes; use with caution.• Do not look int
NOTE: The three products are physically and functionally identical, with the exception of the effective range of transmission and the compliance. In
A bidirectional transceiver can also simultaneously receive a proprietary signal from another transceiver (in any configuration) on its Optical Rx port
FeaturesFiber optic characteristics — The FOX 3G HD-SDI sends and receives digital optical signals via fiber optic small form factor pluggable (SFP) mo
Installation and OperationThis sections details the installation of the FOX 3G HD-SDI, including:• Installation Overview• Mounting the Transceiver•
Kommentare zu diesen Handbüchern