Extron-electronics FOX SW8 Setup Guide Bedienungsanleitung PDF herunterladen

FOX SW8 • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate the

Extron FOX SW8 ber optic switcher.

WARNING: Vision hazard — This unit outputs continuous laser light, which may be harmful

to the eyes; use with caution. For additional safety, plug the attached dust caps into the

optical transceivers when the ﬁber optic cable is unplugged.

CLASS 1 LASER PRODUCT, see the FOX SW8 User Guide, available at www.extron.com.

4 5 6 7 8

FOX SW8

100-240V 0.3A

OPTICAL INPUTS

50/60 Hz

RS-232

OUTPUT

LOOP IN

OUT IN

FOX 500 Tx

100-240V 0.3A

50/60 Hz

AUDIO INPUTS

INPUT LOOP THRU

RGB INPUT

R G B

RS-232

PASS THRU

Tx Rx NA

RS-232

CONTROL

ALARM

OPTIONAL FOR

RETURN DATA

LINK

Tx Rx

1 2

RGB

OPTICAL

1 2*

FOX 500 Tx

100-240V 0.3A

50/60 Hz

AUDIO INPUTS

INPUT LOOP THRU

RGB INPUT

H V

L R

RS-232

PASS THRU

Tx Rx

RS-232

CONTROL

ALARM

OPTIONAL FOR

RETURN DATA

LINK

Tx Rx

1 2

RGB

OPTICAL

POWER

12V

3A MAX

OUTPUT

4/8

OHMS

INPUTS

REMOTE

VOL/MUTE

10V 50mA

MPA 152

LISTED

17TT

AUDIO/VIDEO

APPARATUS

CLASS 2 WIRING

DO NOT GROUND

OR SHORT

SPEAKER OUTPUTS!

Extron

FOX 500 DVI

Fiber Optic Receiver

Flat Panel

Display

DVI Output

Audio Output

RGB Input

Extron

FOX 500 Tx

Fiber Optic

Transmitter

Extron

FOX SW8

Fiber Optic Switcher

Audio Input

Local

Monitor

RGB Input

Extron

FOX 500 Tx

Fiber Optic

Transmitter

8 Inputs

Audio Input

Local

Monitor

Extron

MPA 152

Mini Power

Amplier

Extron

SI 26X

Two-way Ceiling

Speakers

Installation

100-240V 0.3A

50/60 Hz

RS-232

Tx Rx

FOX SW8

OPTICAL INPUTS

LOOP IN LOOP IN LOOP IN LOOP IN LOOP IN LOOP IN LOOP IN OUTIN

12345678

6 3 4 5

3 3

2 2222

NOTE: Steps 2 through 4 are for an 8-input, 1-output switcher in a system that is not HDMI compliant.

For HDCP compliance, the unit can be congured as 7-input, 1-output only. See the NOTE after step 4.

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the FOX switcher as required.

Step 2 — Optical Inputs

Connect up to eight ber optic transmitters to rear panel Input LC connectors of the FOX switcher

(the right-hand connector on each transceiver block).

Step 3 — Loop Optical Outputs

Connect up to seven ber cables between the Loop LC connectors of the FOX switcher (the left-hand connector

on transceiver blocks 1 through 7) and compatible receivers for unswitched outputs (each input loops through to

its associated output only).

OPTICAL

1 2*

OPTIONAL FOR

RETURN DATA

LINK

Transmitter

Receivers

OPTICAL

1 2*

OPTIONAL FOR

RETURN DATA

LINK

Transmitter

Loop (Local)

Application

Switcher

OPTICAL

2* 1

LINK

LOOP IN OUTIN

Switched

Application

OPTICAL

2* 1

LINK

8-input, Non-HDCP

Conﬁguration

1 2

Inhaltsverzeichnis

Seite 1 - FOX SW8 • Setup Guide

FOX SW8 • Setup GuideThis guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX SW8 ber optic swi

Seite 2 - Selected SIS Commands

Step 4 — Switched Optical OutputConnect a ber cable between the Output LC connector on the FOX switcher (the left-hand connector on transceiver block

Kommentare zu diesen Handbüchern

Keine Kommentare

Extron-electronics FOX SW8 Setup Guide Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör für Video Extron-electronics FOX SW8 Setup Guide herunter. Extron Electronics FOX SW8 Setup Guide User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör für Video Extron-electronics FOX SW8 Setup Guide