Extron-electronics MTPX Plus Series User Guide Bedienungsanleitung Seite 20
- Seite / 169
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
c Audio Inputs (local audio) connectors — Connect balanced or
unbalanced stereo audio inputs to these 3.5 mm, 5-pole captive screw
connectors. Connectors are included with each switcher, but you must
supply the audio cable. See figure 7 to wire a connector for the appropriate
input type and impedance level. Use the supplied tie-wrap to strap the audio cable to
the extended tail of the connector. High impedance is generally over 800 ohms.
LR
LR
Unbalanced Stereo Input
Balanced Stereo Input
(high impedance)
(high impedance)
Do not tin the wires!
Ring
Sleeve (s)
Tip
Sleeve
Tip
Sleeve
Tip
Tip
Ring
Figure 7. Captive Screw Connector Wiring for Audio Inputs
CAUTIONS: • The length of exposed wires is critical. The ideal length is 3/16 inch
(5 mm).
•
If the stripped section of wire is longer than 3/16 inch, the
exposed wires may touch, causing a short circuit.
• If the stripped section of wire is shorter than 3/16 inch, wires can
be easily pulled out even if tightly fastened by the captive screws.
• The captive screw audio connector can easily be inadvertently plugged
partially into one receptacle and partially into an adjacent receptacle.
This misconnection could damage the audio output circuits. Ensure
that the connector is plugged fully and only into the desired input or
output.
A mono audio connector consists of a tip and sleeve. A stereo audio connector consists
of a tip, ring and sleeve. See figure 8 to identify the tip, ring, and sleeve parts of the
connector when you are making connections for the switcher from existing audio
cables. The ring, tip, and sleeve wires are also shown on the captive screw audio
connector diagrams, figure 7 and figure 10.
Tip (+)
Sleeve ( )
Sleeve ( )
Ring (
-
)
Tip (+)
RCA Connector
3.5 mm Stereo Plug Connector
(balanced)
Figure 8. Typical Audio Connectors
The audio level for each input can be individually set via the front panel or remote
control to ensure that the level on the output does not vary from input to input (see
“Viewing and Adjusting the Input Audio Level“ in the “Operation” section).
You can also use SIS commands (see the “Programming Guide” section), the Matrix
Switchers Control Program (see the “Matrix Software“ section), or the HTML pages
(see the “HTML Operation” section).
d Input Select switches (switchers other than the
INPUT SELECT
ON
LOCAL
RJ - 45
123
LOCAL
RJ-45
MTPX Plus 128) — For inputs 1 through 3 (matrix sizes 1616 and smaller,
excluding the MTPX Plus 128) or inputs 1 through 6 (matrix sizes 1632 and
larger), set these DIP switches to the Local (up) position to select the local
(RGB video and audio) input. Set the DIP switches to the RJ-45 (down) position
to select the MTP input.
MTPX Plus Series • Installation 14
- MTPX Plus Series 1
- User Guide 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- FCC Class A Notice 3
- Copyright 4
- Trademarks 4
- Contents 5
- Introduction 7
- MTPX Plus 3232 8
- Twisted Pair 8
- Matrix Switcher 8
- TP Cable Advantages 10
- MTP T 15HD A 11
- MTP Transmitter 12
- MTP Receiver 12
- VTT Transmitter 13
- VTR Receiver 13
- Features 14
- Installation 17
- Signal Inputs 18
- Connector 19
- Unbalanced Stereo Input 20
- Balanced Stereo Input 20
- Do not tin the wires! 21
- Signal Outputs 22
- Mono Output 23
- Remote Connection 24
- Ethernet Connection 25
- Reset Button 26
- Power Connection 26
- Operation 28
- MTP MATRIX SWITCHER 29
- Input and Output Buttons 30
- Control Buttons and LEDs 32
- I/O Controls 34
- 2928 30 31 32 35
- Definitions 36
- Front Panel Security Lockouts 36
- Creating a Configuration 37
- 1 2 3 4 5 6 7 8 15 16 38
- 17 18 19 20 21 22 23 24 31 32 38
- VIDEO AUDIO 40
- 1 2 3 4 5 6 7 8 16 41
- 17 18 19 20 21 22 23 24 32 41
- Viewing the Configuration 42
- I/O Grouping 45
- C O N T R O L 46
- Press the button 48
- Using Presets 49
- 1 2 3 4 15 16 50
- 17 18 19 20 31 32 50
- No noticeable 54
- MTPX Plus 1616 54
- MTPX Plus 816, 168, 1616 56
- MTPX Plus 128 56
- Press and hold 57
- 2 seconds 57
- Reading the displayed volume 60
- 17 18 12 63
- 1 2 3 4 12 13 14 15 16 63
- 17 18 19 27 28 29 30 31 32 63
- 1 3 4 5 6 7 8 9 64
- VIDEO AUDIO 65
- File > Save 66
- MATRIX settings as 66
- 1 2 3 16 67
- 17 18 19 32 67
- Press an 69
- Rear Panel Operations 70
- Table 7 71
- Reset Mode Comparison/Summary 71
- Optimizing the Audio 73
- Video Adjustments 73
- Troubleshooting 73
- Configuration Worksheets 74
- Weekly status mtg 3 75
- Programming 79
- Local Host-Control Ports 80
- Ethernet (LAN) Port 81
- Host-to-Switcher Instructions 82
- Switcher-initiated Messages 82
- Switcher Error Responses 83
- } character) 84
- : 0*! clears all ties 86
- (Host to Unit) 87
- (Unit to Host) 87
- Audio output volume 90
- Symbol definitions 99
- Command Function 100
- SIS Command 100
- Response 100
- Additional description 100
- IP setup commands 100
- IP setup commands (continued) 101
- Matrix Software 102
- Installing the Software 103
- Ethernet protocol settings 104
- Finish to exit the wizard 105
- (no Icons or Ties) 108
- IP Settings/Options window 109
- Address and Name fields 110
- Hardware Address field 111
- Use DHCP check box 111
- Sync Time to PC button 111
- E-mail Addressee fields 112
- Updating the Firmware 113
- OK to continue 115
- Begin (see figure 61) 117
- Uploading HTML Files 118
- Windows menus 119
- File menu 119
- Tools menu 120
- Fan is operating properly 123
- Fan has failed 123
- The MTPX Plus fans will 123
- Installed” status 123
- Preferences menu 124
- Using Emulation Mode 125
- Using the Help System 126
- Optimizing the Video 127
- MTPX Skew Setting 128
- MTPX Plus Pre-Peak Selection 129
- C:\Program Files\Extron\ 130
- ButtonLabelGenerator 130
- Start > Programs > 131
- HTML Operation 132
- Download the Startup Page 133
- Status Tab 134
- Select Passwords 135
- Select Firmware Upgrade 135
- Select Email Settings 135
- Date/Time Settings fields 137
- Setting up SMTP authorization 140
- Domain Name field 140
- Email Address fields 140
- File Management Tab 142
- Picture Settings 143
- I/O Settings 143
- Global Presets 143
- MTPX Configuration 143
- Set and View Ties 144
- Changing the skew 145
- Ethernet 152
- Connection 152
- Microsoft Telnet> 155
- Subnetting — A Primer 157
- Reference 159
- Information 159
- Part Numbers and Accessories 163
- Optional Accessories 164
- Mounting the Switcher 165
- Mounting Instructions 166
- Button Labels 167
- Extron Warranty 169
Verwandte Produkte und Handbücher für Audio-Zubehör Extron-electronics MTPX Plus Series User Guide
Audio-Zubehör Extron-electronics MAV Plus series Large Scale Setup Guide Bedienungsanleitung
(21 Seiten)
(21 Seiten)
Audio-Zubehör Extron-electronics CrossPoint Plus Matrix Switchers 84, 88, 124, 128, Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Audio-Zubehör Extron-electronics MAV Plus series Large Scale User Guide Bedienungsanleitung
(186 Seiten)
(186 Seiten)
Audio-Zubehör Extron-electronics RCP 2000 with ISS 506 Support Upgrade Kit Bedienungsanleitung
(2 Seiten)
(2 Seiten)
ProForm 425 CT manuals
Owner’s manuals and user’s guides for Treadmills ProForm 425 CT.
We providing 3 pdf manuals ProForm 425 CT for download free by document types: User Manual
Kommentare zu diesen Handbüchern