Extron-electronics PoleVault Systems PVS 200, 300, and 400 Bedienungsanleitung

PoleVault SystemsInstallation Guide for the PVS 200, 300, and 40068-1390-01 Rev. D03 09

Introduction — Inventory Overview, cont’d1-8PoleVault Systems Installation • Introduction — Inventory Overview1-8N If any items in the PoleVault Syst

1-9PoleVault Systems Installation • Introduction — Inventory Overview 1-9 b. Items not includedThe following items are not included. However, input

PoleVault Systems Installation • Introduction — Inventory Overview1-10Introduction — Inventory Overview, cont’dd. Installation toolsTo aid the profes

2-1PoleVault Systems Installation • Installation Overview Installation OverviewInstallation OverviewThis overview outlines the basic steps for install

PoleVault Systems Installation • Installation — Stage 12-2Stage One — Install the Screen and ProjectorStage 1 This stage involves installing the thre

2-3PoleVault Systems Installation • Installation — Stage 1 1. Mark screen locationa. Mark the center line and the outer edges of screen.T When marki

PoleVault Systems Installation • Installation — Stage 12-4Installation — Stage One, cont’de. Using suitable screws, mount the projector onto the low

2-5PoleVault Systems Installation • Installation — Stage 1 4. Cut the ceiling tilea. Mark the location of the PCM 240 on the T-bar, before removing i

PoleVault Systems Installation • Installation — Stage 12-6Installation — Stage One, cont’d6. Secure the Projector Ceiling Mount to the ceilinga. Att

2-7PoleVault Systems Installation • Installation — Stage 1 T Install any optional power outlets in the 2 gang opening on the mounting plate, towards

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipmen

PoleVault Systems Installation • Installation — Stage 22-8Stage Two — Install the Wall Plates and MLC 104 IP Stage 2This stage involves installing the

2-9PoleVault Systems Installation • Installation — Stage 2 PVT transmitter installation • CAT 5 568A signal transmission cables (connects PVT’

PoleVault Systems Installation • Installation — Stage 22-10Stage Two — Install the Wallplates and MLC 104 IP PlusN The installation must conform to n

2-11PoleVault Systems Installation • Installation — Stage 2 2. Pull cablesThe following cables need to be installed: • CAT 5 cables for signal trans

PoleVault Systems Installation • Installation — Stage 22-12Installation — Stage Two, cont’d3. Install wall platesa. Connect the CAT 5 cables to the r

2-13PoleVault Systems Installation • Installation — Stage 2 4. Install MediaLink ControllerT Before cabling and installing the MLC 104 IP Plus, locat

PoleVault Systems Installation • Installation — Stage 22-14Installation — Stage Two, cont’db. Connect the IR/RS-232 projector communication cable as

2-15PoleVault Systems Installation • Installation — Stage 2 ExtronMLC 104 IP PlusRotate locking armand insert into wallopening.OFFONOFFONExtronCONFIGD

PoleVault Systems Installation • Installation — Stage 32-16Stage Three — Install the PV SI 3C LP Ceiling SpeakersStage 3This stage involves installing

2-17PoleVault Systems Installation • Installation — Stage 3 N The installation must conform to national and local electrical codes, and UL requirem

1-1PoleVault Systems Installation • IntroductionIntroductionOverviewThis manual covers the installation of the Extron PoleVault™ System in a drop ceil

PoleVault Systems Installation • Installation — Stage 32-18Installation — Stage Three, cont’de. Loosen the four screws on the front baffle (counter cl

2-19PoleVault Systems Installation • Installation — Stage 3 c. To terminate the cable, strip the end of the cable 0.2" (5 mm) and secure the wi

PoleVault Systems Installation • Installation — Stage 32-20Installation — Stage Three, cont’d5. Finish speaker installationa. Install/replace the spe

2-21PoleVault Systems Installation • Installation — Stage 4 Stage 4This stage covers installing the devices shown below.LRAUX/MIX IN1B1AINPUTSOUTPUTS2

PoleVault Systems Installation • Installation — Stage 42-22Installation — Stage Four, cont’dN The installation must conform to national and local e

2-23PoleVault Systems Installation • Installation — Stage 4 3. Install the PVS 204SA switchera. Pass two 4-40 x 3/16" screws up through the PMK’

PoleVault Systems Installation • Installation — Stage 42-24Installation — Stage Four, cont’dL RAUX/MIX IN1B1AINPUTSOUTPUTS2B2A43RS-232 MLC/IRDC VOL4/

2-25PoleVault Systems Installation • Installation — Stage 4 FRONTREARRear Plate4c Attach and screw down rear plate4d Replace projector on the adjuster

PoleVault Systems Installation • Installation — Stage 52-26Stage Five — Congure the SystemStage 5Items needed to help complete this stage:• Laptop (

2-27PoleVault Systems Installation • Installation — Stage 5 1d Select MLC 104 IP Plus/PoleVault System from the drop down boxd. Select the MLC 104

PoleVault Systems Installation • Introduction1-2Introduction, cont'dLRAUX/MIX INDO NOT GROUNDOR SHORTSPEAKER OUTPUTS!1B1AINPUTSOUTPUTS2B2A3B3ARS-

PoleVault Systems Installation • Installation — Stage 52-28Installation — Stage Five, cont’d2c Check that an image is present, adjust as neede

2-29PoleVault Systems Installation • Installation — Stage 5 2e Set MLC volume to maximum, and adjust the level on the switcher FRONTREARFrontPlateC

PoleVault Systems Installation • Optional Accessory Installation2-30Optional Accessory Installation — PPC 25The Priority Page Controller (PPC 25) mome

2-31PoleVault Systems Installation • Optional Accessory Installation POWERCNOPAGINGSENSOROUTTIMERELAYSENSITIVITY12V0.5AMAXON12LRRS-232 MLC/IR4/8OhmsAM

PoleVault Systems Installation • Optional Accessory Installation2-32Optional Accessory Installation — PPC 25POWERC NOPAGING RELAYDELAYSENSITIVITY12V0.

2-33PoleVault Systems Installation • Optional Accessory Installation Testing and Adjustment ProcedureThe fully installed system is shown below To tes

PoleVault Systems Installation • Reference Information2-34Reference InformationSpecicationsFor detailed specications and warranty information of the

2-35PoleVault Systems Installation • Reference Information DevicesPVS 204SAExternal power supply ... 100 VAC to 240 VAC, 50/60 Hz, exte

PoleVault Systems Installation • Reference Information2-36Installation — Reference Information, cont’dCeiling mount installation diagram (with item we

1-3PoleVault Systems Installation • Introduction — Planning Before you Begin Installation - PlanningBefore installation is started, you must consider

Extron USA - West Headquarters+800.633.9876Inside USA / Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.633.9876Inside USA / Canada

PoleVault Systems Installation • Introduction — Planning1-4Introduction — Planning, cont’d• Lighting  Type and control (important for projector ima

1-5PoleVault Systems Installation • Introduction — Planning • Viewing obstructions  Pillars, furniture etc., window locations for glare reduction,

PoleVault Systems Installation • Introduction — Inventory Overview1-6Introduction — Inventory Overview2. Inventorya. Included itemsThe PoleVault Sys

1-7PoleVault Systems Installation • Introduction — Inventory Overview PVT CV DWallplatePVT CV D White60-819-13(1) Mud ring (2) Dog legs(2) Dog leg scr