Extron-electronics RGB 472xi_474xi_478xi_478 Mxi Setup Guide Bedienungsanleitung Seite 2
- Seite / 2
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Setup Guide — RGB 472xi/474xi/478xi/478 Mxi, cont’d
68-661-50
Rev. A 03 10
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517
FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2010 Extron Electronics. All rights reserved.
RGB 474xi only
g
Video connector — Connect a composite video device to this female BNC connector for pass-through from a front panel connector (item
s
).
h
S-video connector — Connect an S-video device to this female 4-pin mini-DIN connector for pass-through from a front panel connector (item
t
).
i
Balanced audio connectors — Connect an audio device to this 3.5 mm, 5-pole direct insertion screw connector for pass-through of a balanced audio
output from the front panel connectors (item
e
). See the figure associated with item
u
, on the other side of this sheet to wire the connector. Insert
the wires into the connector and tighten the screws.
j
Network connectors — Connect network devices to these female RJ-45 connectors for pass-through from front panel connectors (item
v
).
Step 4 — Front panel connections and features
N
Items
s
,
t
,
u
, and
v
are present on the RGB 474xi only. On the RGB 478xi, this space holds
AAPs. On the RGB 478 Mxi, this space holds MAAPs.
All models
k
Input 1 and 2 — Connect computer-video sources to these female 15-pin HD connectors.
l
Audio input 1 and 2 — Connect unbalanced stereo audio sources
to these 3.5 mm mini stereo jacks for unbalanced audio input.
m
Input Select button — Press this button to select an input signal.
N
Auto-switch mode, set by DIP switch 8, item
c
, disables the Input
Select button.
n
Power and signal LEDs —
Both red — Power is applied.
Mixed indications — Indicates input selection and signal status as shown
in the table at right.
o
H(orizontal) Shift — While viewing the displayed image, rotate this
control to move the image to the right or left on the screen.
N
DDSP disables the interface’s Horizontal Shift control.
To use the display’s centering controls rather than the interface’s controls, set
DDSP DIP switch 3, item
c
, to On (up).
p
Min/Max LED — This LED flashes when the minimum and maximum
limits of the Horizontal Shift control (item
o
) is reached.
q
Monitor connector — If desired, connect a local monitor or other device
to this female 15-pin HD connector.
r
Monitor switch — Selects which input signal to output on the Monitor connector (item
q
), as follows
Follows (up) — Local monitor display the signal from the selected input.
Input 1 (down) — Locks the local monitor to input 1.
RGB 474xi only
s
Video connector — Connect a composite video source to this female BNC connector for pass-through to a rear panel connector (item
g
).
t
S-video connector — Connect an S-video source to this female 4-pin mini-DIN connector for pass-through to a rear panel connector (item
h
).
u
Audio connectors — Connect unbalanced stereo or mono audio to these female,
left and right, RCA connectors for pass-through to rear panel connectors (item
i
). For mono audio, connect the source to the L/Mono RCA connector. When
DIP switch 7 (item
c
) is set to on (up), the L/Mono input signal is output on both
channels of the rear panel captive screw connector.
v
Network connectors — Connect network devices to these female RJ-45
connectors for pass-through to rear panel connectors (item
j
).
Testing and final installation
Make all connections and test the system. After all devices are powered up, the system
is fully operational. If any problems are encountered, verify that the cables are routed
and connected properly. If your problems persist, call the Extron S
3
Sales & Technical
Support Hotline that is closest to you, at the number shown below.
Install the device when the operation tests satisfactorily.
a. At the power outlet, unplug the power supply.
b. Mount the interface into the wall box.
c. At the power outlet, reconnect the power supply.
Tip (Left) Sleeve (Gnd)
Tip (Left)
Ring (Right)
Sleeve
(Gnd)
S-VIDEO
VIDEO
L/MONO
AUDIO
R
MIN/MAX
WITH ADSP™
RGB 474xi
MONITOR
INPUT 2
INPUT 1
H. SHIFT
INPUT
SELECT
1
2
AUDIO 1
AUDIO 2
INPUT 1
FOLLOWS
MONITOR
C
AT6
14
11
18
= Faceplate screws
DO NOT REMOVE
* RGB 474xi only
17
13
12
16
C
AT6
15
19* 20*
21*
22*
Input selected Input 1 signal Input 2 signal LED 1 LED 2
1 Not present Not present Red Off
2 Not present Not present Off Red
1 Present Not present Green Off
2 Present Not present Amber Red
1 Not present Present Red Amber
2 Not present Present Off Green
1 Present Present Green Amber
2 Present Present Amber Green
Tip (Signal) Sleeve (Gnd)
WI
TH AD
SP™
RGB 478xi
M
ONITOR
H.
S
H
IFT
IN
P
UT
SELECT
MIN/MAX
AUD
IO 1
AU
D
IO
2
IN
P
UT
1
F
O
L
LO
WS
M
ONITO
R
IN
P
U
T
2
I
N
P
U
T
1
1
2
RGB 478xi
1
2
Verwandte Produkte und Handbücher für Hardware Extron-electronics RGB 472xi_474xi_478xi_478 Mxi Setup Guide
(3 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern