Extron-electronics SMX System User Guide Bedienungsanleitung Seite 122
- Seite / 124
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SMX System MultiMatrix Switcher • Reference Information 116
Replacing Button Labels
The button caps are pre-labeled for your convenience. However, you can change them with
the included button labels.
The button assembly consists of a clear lens cap, the button label,
and a white diffuser (see figure 73). Remove the button assembly
from the SMX as follows:
1. Make new labels using either the blanks on page 119 or the
Button Label Generator software. Cut the labels out.
2. Remove the button assembly by inserting a small, flat head
screwdriver, between the button base and the diffuser to
gently pry the button assembly off the button plunger, as
shown in the drawing at right.
3. Locate the small corner notch on the lens cap, and slide the
screwdriver between the lens cap and the diffuser (see 1 in
figure 73).
4. Rotate the screwdriver and carefully pry the two pieces apart
(see 2 in the figure 73).
Base (inside front panel)
1
. Separate the
two-piece button
cap from the base.
2. Pry apart the two pieces
(lens and diffuser)
at the corner.
3. Remove and replace
label as desired.
TEXT
Diffuser
Button Label
Clear Lens
Figure 73. Replacing a Button Label
5. Lift out the transparent square label that you want to replace. You may need to use the
small screwdriver to gently pry the label out.
6. Insert one of the new labels you created in step 1 into the clear button cap, align the
white backing plate with the cap, and firmly snap it into place.
7. Gently, but firmly, press the reassembled button into place on the SMX front panel.
8. Repeat steps 1 through 7 as needed to relabel other buttons.
Pry the button
from the base.
- User Guide 1
- SMX System 1
- www.extron.cn，参见 Extron 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- Introduction 7
- Definitions 9
- Features 10
- Installation and 12
- Power and Control Connections 13
- Input and Output Boards 14
- ADDRESS 15
- Other I/O Boards 16
- Installing the I/O Boards 16
- Reconfig 17
- Wiring the Audio Connectors 18
- Operation 19
- I/O Plane Selection Buttons 20
- Input and Output Buttons 20
- Control Buttons 21
- Power Indicator LEDs 21
- Powering Up 22
- Front Panel Operation 22
- Creating Ties 23
- Viewing Ties 24
- Removing Ties 25
- Replacing Ties 26
- Muting an output 27
- Unmuting an output 28
- All buttons extinguish 29
- (here preset 8, 18, and 32) 29
- Plane button lights green 30
- C O N T R O L 31
- Using the Front Panel 33
- Using Reset Levels 37
- Modes 3, 4, and 5 38
- Troubleshooting 39
- SIS Configuration 40
- Connection Timeouts 41
- Number of Connections 41
- Using Verbose Mode 41
- SIS Programming Guide 42
- Switcher Error Responses 43
- reference 46
- SIS value 47
- Resolution Refresh (Hz) 47
- X2@*X1$ 49
- 1 = on 49
- 00 52
- nnnn = actual rate 55
- 01 = bypass the reclocker 55
- Verbose mode 2 and 3 58
- 0 = Off or disabled 58
- –12.0 - +14.0 59
- queries 60
- X8# = I, then X8$ = 00 61
- (SMX-00-02-3D) 62
- 00 = fan and power supply 64
- SMX Control 65
- Software 65
- Starting the Program 66
- Using Emulation Mode 67
- Using the Program 68
- File menu 69
- Tools Menu 70
- Audio-input-Config 77
- Preferences 78
- Master-Reset 80
- Customizing the SMX Window 81
- Managing Ties 82
- IP Settings/Options 83
- Setting the IP address 84
- Setting the subnet mask 85
- Hardware address field 85
- Enabling daylight saving time 87
- Setting the user password 87
- Updating the firmware 89
- Uploading HTML files 91
- HTML Configuration 93
- System Status Pages 95
- Physical Configuration 96
- Configuration Pages 97
- Date/Time Settings fields 99
- Passwords Page 100
- Email Settings Page 100
- Email Address Fields 101
- Firmware Upgrade Page 102
- File Management Page 103
- Control Pages 104
- To set or replace ties 105
- To remove ties 105
- To set input audio levels 106
- To set output volume levels 107
- To mute or unmute a signal 108
- EDID configuration 109
- Presets Page 110
- Recalling a global preset 111
- Recalling a plane preset 111
- Ethernet Control 112
- Connect as a Telnet Client 115
- Telnet tips 116
- Escape character and Esc key 116
- Local echo 116
- Subnetting — A Primer 117
- Subnet Masks and Octets 118
- Reference 119
- Information 119
- Button Labels 120
- Replacing Button Labels 122
- Button Label Blanks 123
- Contact Information 124
- Extron Warranty 124
Verwandte Produkte und Handbücher für Hardware Extron-electronics SMX System User Guide
(1 Seiten)
(2 Seiten)
(59 Seiten)ProForm 425 CT manuals
Owner’s manuals and user’s guides for Treadmills ProForm 425 CT.
We providing 3 pdf manuals ProForm 425 CT for download free by document types: User Manual
Kommentare zu diesen Handbüchern