Extron electronics CVEQ 100 Series Einstellungsanleitung PDF herunterladen

Setup Guide — CVEQ/SVEQ 100 Series

This guide provides basic instructions for

an experienced installer to set up and operate

the Extron

CVEQ 100 Series and the SVEQ 100

Series of line drivers.

Installation and service must be performed

by authorized personnel only.

Installation

Step 1 — Turn off the line driver and input/output devices

Turn the input and output devices off and unplug their power cords. Verify that the line

driver is disconnected from the power source before proceeding.

Step 2 — Attach output cables

For the CVEQ 100 Series, connect a composite video output device to the female BNC

connector.

For the SVEQ 100 Series, connect a S-video output device to the female BNC connectors.

For audio output, wire a balanced/unbalanced audio output device to the 3.5 mm, 5-pole,

direct insertion captive screw connector.

Step 3 — Attach input cables

For the CVEQ 100 Series, connect a composite video input source to the connector (RCA

or BNC, depending on model).

For the SVEQ 100 Series, connect an S-video input source to the connector (4-pin mini

DIN or BNCs, depending on model).

For audio input, connect an unbalanced stereo audio source to the left and right RCA

connectors.

Step 4 — Power on the line driver

Wire the power connector (see ﬁgure 1).

When power is applied to the unit, the

front panel LED lights.

Always use a power supply

supplied and or speciﬁed

by Extron. Use of an

unauthorized power supply

voids all regulatory compliance

certiﬁcation and may cause

damage to the supply and the

end product. Unless otherwise

stated, the AC/DC adapters are not suitable for use in air handling spaces or in

wall cavities. The installation must always be in accordance with the applicable

provisions of National Electrical Code ANSI/NFPA 70, article 75 and the Canadian

Electrical Code part 1, section 16. The power supply shall not be permanently ﬁxed

to building structure or similar structure.

Step 5 — Power on devices and check for picture and sound

Connect the power cords and turn on the output devices and input devices.

The picture should appear and sound should be audible. If not, ensure that all devices are

plugged in and receiving power. Check the cabling and make adjustments as needed.

SECTION A–A

Ridges

Smooth

Power Supply

Output Cord

A A

Captive Screw

Connector

3/16”

(5 mm) Max.

Figure 1 – Power connector wiring

1 2

Inhaltsverzeichnis

Seite 1 - — CVEQ/SVEQ 100 Series

Setup Guide — CVEQ/SVEQ 100 SeriesThis guide provides basic instructions for an experienced installer to set up and operate the Extron® CVEQ 100 Se

Seite 2 - Troubleshooting

Extron USA - West Headquarters+800.63 3.9876Inside USA / Canada Only+1.714.4 91.1500+1.714.4 91.1517 FAXExtron USA - East+800.63 3.9876Inside USA / Ca

Weitere Dokumente für Netzwerk-Switches Extron electronics CVEQ 100 Series

Um das Dokument anzuzeigen Extron electronics CVEQ 100 Series Bedienungsanleitung

Extron electronics CVEQ 100 Series Bedienungsanleitung (12 Seiten)

Extron electronics CVEQ 100 Series Bedienungsanleitung (19 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Extron electronics CVEQ 100 Series Einstellungsanleitung

Stöbern Sie online oder laden Sie Einstellungsanleitung nach Netzwerk-Switches Extron electronics CVEQ 100 Series herunter. Extron electronics CVEQ 100 Series Setup guide Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Netzwerk-Switches Extron electronics CVEQ 100 Series

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Netzwerk-Switches Extron electronics CVEQ 100 Series