Extron-electronics SME 100 User Guide Bedienungsanleitung Seite 148
- Seite / 185
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Command
ASCII Command
(host to unit)
Response
(unit to host)
Additional Description
Audio bit rate
Set audio bit rate
E
A
X6$
BITR
}
Bitr
A
X6$ ]
Set the audio bit rate value of
the output to
X6$
.
View
E
A BITR
}
X6$ ]
View the currently set output
bit rate separated values.
Audio sample rate
Set sample rate
E X6%
AUSR
}
Ausr
X6% ]
Set the audio sample rate value
of the output to
X6%
.
View
E
AUSR
}
X6% ]
View the currently set sample
rate value.
Advanced Configurations
Test pattern
Select test pattern
E X2)
TEST
}
Test
X2) ]
Set the test pattern to
X2)
.
View
E
TEST
}
X2) ]
View the current test pattern.
Input aspect ratio
Set to fill
E X!
*1 ASPR
}
Aspr
X!
*1
]
Set input
X!
to always fill the
entire output raster (default).
Set to follow
E X!
*2 ASPR
}
Aspr
X!
*2
]
Set input
X!
to correctly setup
each input rate with its native
aspect ratio.
View
E X!
ASPR
}
X3( ]
View the currently set aspect
ratio for input
X!
.
Power save mode
Set power save
mode
E X4)
PSAV
}
Psav
X4) ]
Enable or disable the power
save mode.
View
E
PSAV
}
X4) ]
View the currently set power
save mode.
Overscan mode: applies only to SMPTE (480p – 1080p) input rates
Set overscan mode
E
X#
*
X7^
OSCN
}
Oscn
X#
*
X7^ ]
Set input video format
X#
to
overscan mode
X7^
.
View
E X#
OSCN
}
X7^ ]
View the currently set overscan
mode for the input video format
X#
.
NOTES:
X! = Input selection 1 through 3 (2 and 3 applicable for EDID only)
X# = Input video format 1 through 7, 9, 11 (see Input video format on page 126)
X2) = Test pattern 0 through 15 (see Test pattern on page 127; default = 0)
X3( = Aspect ratio settings 1 = Fill (default), 2 = Follow
X4) = Power save mode 0 = Power save mode disabled (default), 1 = Power save mode enabled
X6$ = Audio bit rate (kbps) 16 through 384 (default = 384)
X6% = Audio sample rate 3 = 48 kHz (default)
X7^ = Overscan 0 through 2 (see Overscan on page 130)
SME 100 • Remote Communication and Control 142
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Verwandte Produkte und Handbücher für Hardware Extron-electronics SME 100 User Guide
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern