Extron-electronics SME 100 User Guide Bedienungsanleitung Seite 51
- Seite / 185
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Using the Front Panel Lock (Executive Mode)
To prevent accidental changes to settings, enable the front panel lock (executive mode) on
the SME100 by pressing the Menu and Next buttons simultaneously for two seconds. The
front panel lock disables all of the front panel controls, but allows communication and control
changes through the RS-232 connector, Config port, and the web-based user interface. To
disable the front panel lock (executive mode), press and hold the Menu and Next buttons
simultaneously for two seconds.
When front panel lock is enabled, the LCD display shows Exe Mode Enabled for
approximately two seconds and then returns to the default display cycle (see figure 26).
When front panel lock is disabled, the LCD display shows Exe Mode Disabled for
approximately two seconds and then returns to the default display cycle (see figure 27).
NOTES:
• For information on enabling and disabling the front panel lock using the
web-based user interface, see the "Encoder Settings Page" section on page 88.
• For information on enabling and disabling the front panel lock using
SIS commands, see "Front panel lock (executive mode)" on page 154 of the
"Command and Response Table for SIS Commands" section.
Menu
Press for
2 seconds
Next
2 second
timeout
EXE MODE
ENABLED
Default Display Cycle
2 sec.
2
sec.
In#1 YUVp/HD
480p
640 x 480
OUTPUT A/V
BR 521 Kbps
UNICAST RTP
2
sec.
SME 100 HD/SD
FW V2.00
2 sec.
In#1 YUVp/HD
31kHz 60Hz
2
sec.
+
Figure 26. Enable Front Panel Lock (Executive Mode)
Menu
Press for
2 seconds
Next
2 second
timeout
EXE MODE
DISABLED
+
Default Display Cycle
2 sec.
2
sec.
In#1 YUVp/HD
480p
640 x 480
OUTPUT A/V
BR 521 Kbps
UNICAST RTP
2
sec.
SME 100 HD/SD
FW V2.00
2 sec.
In#1 YUVp/HD
31kHz 60Hz
2
sec.
Figure 27. Disable Front Panel Lock (Executive Mode)
SME100 • Front Panel Operation 45
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Verwandte Produkte und Handbücher für Hardware Extron-electronics SME 100 User Guide
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.235 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern